Wood Finishing Techniques Tung Oil Sample Plans PDF

Tung oil seeps into the grain of the wood, giving it a perpetual wet look that highly accentualizes the grain of the wood, commonly referred to as making the grain pop. Tung oil provides a relatively hard surface finish that, as long as the surface integrity is intact, provides a waterproof finish that is impervious to dust, alcohol, acetone (nail polish remover), and various acids such as fruit and vegetable acids (orange juice). What I will present here is the most simple and straightforward technique, and I will identify optional steps as such. Oil and wax wood finishes are a great choice for many projects. Tung oil dries a little bit faster than linseed oil, and sometimes it is modified to cure even more quickly. Our Tung Oil is a great wood finish that penetrates deep into the wood. Creates water resistant surface. Visit our site or call (800) 339-9748 to learn more.

wood finishing techniques tung oil 2Minwax Tung Oil Finish is an oil-based wood finish that gives wood a lustre while also providing a tough layer of protection. For additional gloss, apply another coat of Minwax Tung Oil Finish, 24 hours from application of previous coat. Wood finishing tips, techniques and advice. Tung oil or China wood oil is a drying oil obtained by pressing the seed from the nut of the tung tree (Vernicia fordii). Tung oil has become popular as an environmentally friendly wood finish, but it should be noted that many products labelled as tung oil finishes are deceptively labelled: polymerized oils, wiping varnishes, and oil/varnish blends have all been known to be sold as tung oil finishes (sometimes containing no tung oil at all), and all the above contain solvents and/or chemical driers. The traditional technique for applying pure tung oil is to dilute the oil 1:1 with solvent, then apply a succession of very thin films with a soft non-fuzzy cloth such as tee-shirt cotton. Comparing BLO (boiled linseed oil) to (pure) tung oil is like comparing apples to oranges. Woodworkers have used linseed oil in wood finishes for a long time because it was readily available, flax being grown easily all over the world. Getting good results requires using the right techniques and not being in a hurry.

Wipe, brush or spray the finish onto the wood; keep the wood wet with the finish for 5 to 10 minutes, or until it stops soaking in; then wipe off the excess and allow the finish to cure overnight at room temperature. But tung oil is too difficult for most people to use by itself as a finish. Essential Cabinetmaking Techniques Project Download. Pure Tung Oil provides a hard and tough surface finish that is absolutely waterproof; The guy building it said he will only finish it with tung oil, and that the piece will need to be refinished on a periodic basis. The heated linseed oil penetrates the surface of the wood, adding greater visible depth to the wood, revealing the grain pattern. Tung oil finishes like this are often applied with a wipe-on technique that can only leave a very thin film on the surface of the wood.

Minwax Tung Oil Finish

Unlike tung oil, which dries inside the wood, surface finishes such as shellac and varnish dry on top of the wood to create a protective coating. To remove the roughness from a final finish, try the technique known as wet sanding, which eliminates dried-on dust without leaving visible sandpaper scratches. Leave the wood unfinished. Or use tung oil. Tung oil is dead easy to use, builds well, dries quickly, and produces a durable, clear finish with contrast and depth. I’d only add that in comparing boiled linseed oil to tung oil, the biggest difference between the two is that tung oil is quite a bit more water-resistant than linseed. What finish do you recommend for a very porous wood? This is yet another reason why Waterlox Original Tung oil finishes are the choice for so many. Therefore, wood finishes were very labor intensive and very expensive to apply and maintain. This finishing technique can be used in many applications such as wood floors, decks, docks, concrete floors, outdoor wood furniture, wood counter tops and many other porous surfaces. Tung oil is one of the easiest wood finishing techniques. First make sure the wood is sanded down with 400 grit sandpaper. Some people like to go a step further and sand down to 600 grit but, I find that 400 gives very good results.

Oil Finishes: Their History And Use

Finishing wood can take days and even weeks, but there are a few natural and easy wood finishes that Ben Light recommends as alternatives. Gather the materials: Tung oil, furniture wax, a bunch of clean rags (cut up T-shirts work great), rubber gloves. I want the natural wood look with low gloss, so I plan on rubbing in quite a few coats of tung oil finish. Tung oil finish is varnish, highly thinned varnish, so your coats are very thin and you’ll need very many. Woodworking Techniques (349). The stained grain filler lodges into the walnut wood pores and only gently colors the wood for a high-contrast effect. If you like the look of an oil finish, consider trying tung oil varnish. There s very little skill needed to apply gel, whereas brushing a finish requires some techniques. Learn when and how to use a variety of finishes on your wooden furniture. Danish and tung oil finishes are far superior to the traditional linseed oil; linseed oil is sticky and hard to apply. Any oil finish must be reapplied periodically, but Danish and tung oil require far less reapplication than linseed oil.

Waterlox has been using tung oil as the ideal base in wood finishes for over 90 years. Draft Format Article on Tung Oil Padding Techniques, we’re developing this article to present some of our finishing practices. Cabot Tung Oil Finish imparts a striking hand-rubbed beauty to both bare and stained wood surfaces. Allow wood that has been stained with an oil-based stain to dry at least 24 hours. Learn tips and techniques to protect wood against the elements. Now, when I finish floors with Tung oil I use Waterlox products, old school lambswool applicator and do four coats. We all need to explore wood related finishing techniques which are outside of our floor supply store bubble.